Home › Technical articles

Đọc bằng tiếng Việt

1734-AENTR and 1794-AENTR status indicators: meanings, IP address switches, web pages, replacement

TDL Industrial Automation · Last updated:

From Rockwell's 1734-IN040C, 1734-UM017F, 1794-UM066E and installation instructions: every Module, Network, POINTBus, power and Link indicator state on the 1734-AENTR and 1794-AENTR (with the 1734-AENT and 1794-AENT), the documented actions, IP switches and 888, the diagnostic web pages, implicit protected mode and what to redo after a replacement.

The POINT I/O 1734-AENTR shows eight status indicators: Module status, Network activity, Network status, POINTBus status, System power, Field power, and a Link indicator for each of its two ports. The FLEX I/O 1794-AENTR shows only four: Link 1, Link 2, Module Status and Network Status. On both, flashing red on Network status means a connection timed out and solid red means a duplicate IP address. Below: every state with Rockwell's meaning and action, the IP switches, the web pages and what to redo after a replacement.

Status indicators on the 1734-AENTR and 1794-AENTRTwo-column schematic, grouped by function, not by physical position on the module. Left: POINT I/O 1734-AENTR adapter per 1734-IN040C. Right: FLEX I/O 1794-AENTR adapter per 1794-UM066E. Row 1, module: Module status, flashing green means needs commissioning, solid red means unrecoverable fault; Module Status, flashing green means not configured, red means major fault. Row 2, network: Network status and Network activity; Network Status; flashing red means a CIP connection timed out, solid red means duplicate IP address. Row 3, ports: Link 1 and Link 2 on both adapters, green is 100 Mbps, yellow is 10 Mbps, flashing means traffic. Row 4, backplane: POINTBus status, flashing red means module count mismatch, missing module or I/O timeout; the 1794-AENTR indicator table has no Flexbus indicator. Row 5, power: System power and Field power; the 1794-AENTR has no separate power indicator, Module Status off means no 24 V DC. Row 6, address switches: thumbwheel 001 to 254, 888, 999 and 801 to 864 for chassis size; IP address switches 001 to 254, 888, 999.Status indicators on the 1734-AENTR and 1794-AENTR1734-AENTR · POINT I/Oper 1734-IN040C, 12/20181794-AENTR · FLEX I/Oper 1794-UM066E, 12/20251 · ModuleModule statusflashing green: needs commissioning;solid red: unrecoverable faultModule Statusflashing green: not configured; red: major,unrecoverable fault2 · NetworkNetwork status, Network activityflashing red: CIP connection timed out;solid red: duplicate IPNetwork Statusflashing red: connection timed out;red: duplicate IP3 · Ethernet portsLink 1, Link 2green: 100 Mbps; yellow: 10 Mbps;flashing: trafficLink 1, Link 2green: 100 Mbps; yellow: 10 Mbps;flashing: traffic4 · BackplanePOINTBus statusflashing red: module count mismatch, missingmodule or I/O timeoutNo Flexbus indicatorthe indicator table lists only Link,Module Status and Network Status5 · PowerSystem power, Field power5 V DC-DC output; 24 V field powerNo separate power indicatorModule Status off: no 24 V DC at the adapter6 · Address switches3-digit thumbwheel001 to 254, 888, 999; 801 to 864 setsthe chassis size3-digit IP address switches001 to 254, 888, 999Grouped by function, not by physical position on the module. Based on Rockwell Automation 1734-IN040C,1734-UM017F and 1794-UM066E, read 15 November 2026. Figure: drawn by TDL.
Figure 1: Status indicators on the 1734-AENTR and 1794-AENTR. On a phone, swipe sideways to see the whole figure.

1. Which adapters and which documents

Adapter Document used here Lifecycle on Rockwell's page (read 15 November 2026)
1734-AENTR, Series C 1734-IN040C (12/2018), 1734-UM017F (05/2023) Active
1734-AENT, Series C 1734-IN042J (06/2026) Active
1794-AENTR and 1794-AENTRXT 1794-UM066E (12/2025), 1794-IN131E (06/2024) Active Mature; "Replacement Available" with no product named
1794-AENT, Series B 1794-IN082G (06/2024) End of Life, discontinued date 30 September 2028; functional replacement 1794-AENTR

Both have two 10/100 Mbps Ethernet ports; on the 1794-AENTR they sit on the underside (1734-IN040C p. 18; 1794-IN131E pp. 4, 9). Module counts, POINTBus current and RPI are in choosing remote I/O adapters, rings in DLR or PRP. Setting up a Stratix 5200 switch for the DLR ring itself is covered in Stratix 5200 setup.

2. 1734-AENTR indicators

From 1734-IN040C pp. 15–17; actions only where the table gives one.

Indicator State Meaning and action
Module status Off No power applied
Flashing green Needs commissioning: configuration missing, incomplete or incorrect
Solid green Operating normally
Flashing red Recoverable fault: complete the firmware update, verify the address switches
Solid red Unrecoverable fault; the adapter may need replacing
Flashing red/green Self-test
Network status Off Not online: duplicate MAC ID test not finished, or no power; check Module status
Flashing green Online, no CIP connections
Solid green Online, CIP connections established
Flashing red One or more CIP connections timed out (POINT Guard I/O timeouts excluded): check for an I/O module failure and controller operation
Solid red Duplicate IP address: verify and correct the IP setting
Flashing red/green Self-test
POINTBus status Off Not online: check Module status and power
Flashing green Online, no connections; also during a firmware (NVS) update
Solid green Online, connections established
Flashing red Recoverable fault: module count mismatch at power cycle, missing module, or I/O connection timeout
Solid red Unrecoverable fault, adapter bus off
Flashing red/green Power-up test
System power Off / green Off: adapter power off or DC-DC converter problem; green: 5 V DC-DC output active
Field power Off / green Off: adapter power off; green: 24 V input present
Network activity, Link 1, Link 2 Off No link
Green Link at 100 Mbps; flashing: traffic at 100 Mbps
Yellow Link at 10 Mbps; Link 1 or 2 flashing yellow: traffic at 10 Mbps

The single-port 1734-AENT Series C has the same Module status, Network activity, Network status, POINTBus status, System power and Field power indicators, but no Link 1 and Link 2 (1734-IN042J pp. 8–9).

3. 1794-AENTR indicators

From 1794-UM066E pp. 45–46; the actions match 1794-IN131E p. 8. The table has no Flexbus indicator and no power indicator: Module Status off is how the adapter shows missing power.

Indicator State Meaning and action
Link 1, Link 2 Off No link: check the network cabling
Green / flashing green Link at 100 Mbps / traffic at 100 Mbps
Yellow / flashing yellow Link at 10 Mbps / traffic at 10 Mbps
Module Status Off No 24 V DC: confirm power reaches the adapter
Flashing green Standby, not configured: configure the adapter
Green Operating correctly
Flashing red Minor, recoverable fault, often an incorrect or inconsistent configuration: check and reconfigure
Red Major, unrecoverable fault: cycle power; if it stays, replace the adapter
Flashing red/green Power-up self-test
Network Status Off Not powered or no IP address: check power, wiring and configuration
Flashing green IP address, no connections
Green IP address and at least one CIP connection
Flashing red A connection with the adapter as target timed out
Red Duplicate IP address: assign a unique address
Flashing red/green Power-up self-test

The 1794-AENT Series B has the same Module status and Network status states and one Link status indicator (1794-IN082G pp. 9–10).

4. Reading them together

  • Network status flashing red. A connection timed out. Rockwell's first check on POINT I/O is an I/O module failure and the controller. The codes the controller shows for a lost connection, such as 16#0203 or 16#0204, are explained in ControlLogix I/O fault 16#0204, 16#0203.
  • Network status solid red. Another device holds the same IP address.
  • POINTBus status flashing red. One cause the table names is a module count mismatch. On a new or replaced 1734-AENTR, check the chassis size: the adapter allows no I/O connection until the module count matches its stored chassis size (1734-UM017F pp. 13–15).
  • Link yellow. The port linked at 10 Mbps; for Stratix switch ports see Stratix 5700 and 5400 troubleshooting.

5. IP address: switches, DHCP and 888

Switch setting 1734-AENTR 1794-AENTR
001–254 Sets the network address; gateway 0.0.0.0 at 001, 192.168.1.1 at 002–254 192.168.1.xxx, mask 255.255.255.0; gateway 0.0.0.0 on firmware 1.013 and earlier; with firmware 1.014, 192.168.1.1 at 002–254
999 As shipped, DHCP enabled As shipped, DHCP enabled
888 Restores factory defaults After a power cycle: DHCP on, auto-negotiation on, both ports disabled, configuration password blank; return the switches and cycle power to re-enable the ports
801–864 Chassis size (firmware 5.015 or later); Ethernet ports disabled while set Not used
Other (000, above 254) DHCP if enabled, else the address stored in memory Same

Sources: 1734-IN040C pp. 9–10, 1734-UM017F pp. 13–15, 34–35; 1794-UM066E pp. 16–17, 54.

On the 1794-AENTR, BOOTP needs the adapter's Ethernet hardware (MAC) address, printed on a label on the front; RSLinx Classic is the other method listed (1794-UM066E pp. 19, 21). 1734-UM017F calls for a fixed address and keeps DHCP for initial configuration only, because a renewed DHCP lease may bring a different address and stop communication (p. 41).

6. Built-in web pages

1734-AENTR. The web server is on by default from firmware 2.011 and can be switched off (1734-UM017F p. 44). Appendix A covers login rules, the diagnostic pages (Diagnostic Overview, Network Settings, Ethernet Statistics, I/O Connections, Advanced Diagnostics), the Identity, Network Configuration and Services pages, and Browse Chassis (pp. 101–118).

1794-AENTR. The web server is on by default on firmware 1.016, 1.017, 2.011 and 2.012, and off from 2.013, also after a factory reset. It is switched on in Module Properties, Servers tab, with the adapter inhibited, or by a CIP explicit message (pp. 49–50). The password must be changed at first login, and a third failed attempt locks login for one minute (p. 51). Diagnostic Overview shows CIP connection statistics, Ethernet Statistics the link, interface and media counters, and I/O Connections the Class 1 connections (pp. 52–54). SNMP is off by default from 2.013 and the manual recommends keeping it off (pp. 24–25).

7. Implicit protected mode

Both adapters block changes while I/O connections run through or to them; the mode ends when all those connections stop and cannot be configured. On the 1734-AENTR it blocks IP and port-speed changes, firmware updates, enabling or disabling ports and remote resets (1734-UM017F pp. 41–42). On the 1794-AENTR it also blocks factory and adapter resets, web server and SNMP switching, web configuration changes and the web password change (1794-UM066E pp. 22–23).

8. Replacing an adapter

Do not remove or replace an adapter under power; on POINT I/O, interrupting the backplane can cause unintended machine motion (1734-UM017F p. 26; 1734-IN040C p. 9; 1794-UM066E p. 14).

  • 1734-AENTR. After fitting it, set the network address, IP address and chassis size (1734-UM017F p. 27). The controller does not send the chassis size in its connection request (p. 15), so a new adapter starts at the default of 1 (p. 13). The 1734-AENTR accepts 1734-AENT keying (1734-IN040C p. 7).
  • 1794-AENTR. The Flexbus connector is unplugged and plugged back as part of the swap (1794-UM066E pp. 14–15). With BOOTP, enter the new adapter's hardware address (p. 19). On firmware 2.013 or later the web server and SNMP are off until switched on again (pp. 24, 49).
  • Firmware. 1794-UM066E points to the Product Compatibility and Download Center (PCDC) for firmware, AOP and EDS files (p. 7); its compatibility table starts at Studio 5000 Logix Designer 20 and RSLinx 2.59 (p. 10). 1734-UM017F points to the PCDC to verify module compatibility (p. 12). The update itself: ControlLogix and CompactLogix firmware updates.

What we check first

This is TDL's practice, not a Rockwell requirement.

  • We photograph the indicators and switch positions before anyone touches the rail.
  • On a solid red Network status we look for the second device on that address, including any DHCP server on the segment.
  • On a yellow Link we check the switch port before the cable.
  • We record catalog number, series, firmware, chassis size, IP method and web server state of every adapter with the program backup.
  • Because protected mode blocks IP and firmware changes, we agree a machine stop before that work.

Remote I/O work at TDL

TDL Industrial Automation is a System Integrator in the Rockwell Automation PartnerNetwork. At Crown Da Nang we replaced DeviceNet with EtherNet/IP on a body maker, with POINT I/O adapters for the body maker and trimmer. The Intel Vietnam SWTP control system we delivered runs on Flex remote I/O. See also breakdown support, Rockwell Automation upgrades and FLEX I/O to FLEX 5000.

Frequently asked questions

What does a flashing red Network status mean on a 1734-AENTR?

One or more CIP connections timed out. 1734-IN040C says to check for an I/O module failure and controller operation; the controller reports the lost connection with a code such as 16#0203 or 16#0204.

Why is the POINTBus status flashing red after replacing a 1734-AENTR?

A module count that does not match the stored chassis size is one documented cause. The controller does not send the chassis size, a new adapter starts at 1, and no I/O connection is allowed until the module count matches. It is set with the thumbwheel at 801 to 864 on firmware 5.015 or later.

What does solid red Network Status mean on a 1794-AENTR?

A duplicate IP address. Another device uses the same address; assign a unique one.

Why can't I change the IP address or firmware of a running adapter?

Implicit protected mode. While I/O connections run through or to the adapter, both the 1734-AENTR and the 1794-AENTR reject IP changes and firmware updates until every connection stops.

Does the 1794-AENTR have a web page?

Yes, with diagnostic pages for CIP connections, Ethernet statistics and I/O connections. From firmware 2.013 the web server is off by default and is switched on in Module Properties with the adapter inhibited.

Sources

  • Rockwell Automation, 1734-IN040C-EN-P, POINT I/O Dual Port EtherNet/IP Adapter Installation Instructions (1734-AENTR), 12/2018 — pp. 7, 9–12, 15–18
  • Rockwell Automation, 1734-UM017F-EN-E, POINT I/O and ArmorPOINT I/O Dual-port EtherNet/IP Adapters User Manual, 05/2023 — pp. 12–15, 26–27, 34–35, 41–44, 101–118
  • Rockwell Automation, 1734-IN042J-EN-P, POINT I/O EtherNet/IP Adapter Installation Instructions (1734-AENT, 1734-AENTK Series C), 06/2026 — pp. 8–9
  • Rockwell Automation, 1794-UM066E-EN-E, FLEX I/O Dual-port EtherNet/IP Adapters User Manual, 12/2025 — pp. 7, 10, 14–17, 19, 21–25, 45–46, 49–54
  • Rockwell Automation, 1794-IN131E-EN-P, FLEX I/O Dual-port EtherNet/IP Adapter Installation Instructions (1794-AENTR, 1794-AENTRXT), 06/2024 — pp. 4, 8–9
  • Rockwell Automation, 1794-IN082G-EN-P, FLEX I/O EtherNet/IP Adapters Installation Instructions (1794-AENT, 1794-AENTK Series B), 06/2024 — pp. 9–10
  • Rockwell Automation, product pages 1734-AENTR, 1734-AENT, 1794-AENTR and 1794-AENT (lifecycle status, discontinued date, replacement)

Read 15 November 2026. This article paraphrases the sources and does not quote them; read the original documents before designing or working on a system.

Related services:
Breakdown support & resident engineers Rockwell Automation upgrades